I am using a datalogger with the path "Meas/HR" to record data. Start the datalogger with a double tap, and the session begins without issue. Double-tapping the sensor again will end the session and save the data. Nevertheless, if I use the path "/Meas/Acc/104," the datalogger starts successfully with a double-tap. However, the issue arises when trying to stop the session by double-taping on the sensor, as it doesn't work in this scenario.
Subscribe or Unsubscribe to DOUBLETAP detection
bool DataLoggerClient::startModule()
{
mModuleState = WB_RES::ModuleStateValues::STARTED;
setShutdownTimer();
// Subscribe to DOUBLETAP detection
asyncSubscribe(WB_RES::LOCAL::SYSTEM_STATES_STATEID(), AsyncRequestOptions::Empty, WB_RES::StateIdValues::DOUBLETAP);
return true;
}
void DataLoggerClient::stopModule()
{
wb::ResourceProvider::stopTimer(mTimer);
mTimer = wb::ID_INVALID_TIMER;
// Unsubscribe DOUBLETAP detection
asyncUnsubscribe(WB_RES::LOCAL::SYSTEM_STATES_STATEID(), AsyncRequestOptions::Empty, WB_RES::StateIdValues::DOUBLETAP);
mModuleState = WB_RES::ModuleStateValues::STOPPED;
}
we are set internal resister in DoubleTAPConfig();
void DataLoggerClient::onSubscribeResult(wb::RequestId requestId,
wb::ResourceId resourceId,
wb::Result resultCode,
const wb::Value& rResultData)
{
DEBUGLOG("DataLoggerClient::onSubscribeResult() called.");
switch (resourceId.localResourceId)
{
case WB_RES::LOCAL::SYSTEM_STATES_STATEID::LID: {
if (resultCode == whiteboard::HTTP_CODE_OK)
{
DEBUGLOG("DoubleTAPConfig()");
// set internal resistor value for DataLoggerClient mode
DoubleTAPConfig();
}
break;
}
}
}
we are get notification in that section.
void DataLoggerClient::onNotify(wb::ResourceId resourceId, const wb::Value& value, const wb::ParameterList& parameters)
{
DEBUGLOG("DataLoggerClient::onNotify");
switch (resourceId.localResourceId)
{
case WB_RES::LOCAL::SYSTEM_STATES_STATEID::LID: {
const WB_RES::StateChange& stateChange = value.convertTo<const WB_RES::StateChange&>();
if (stateChange.stateId == WB_RES::StateIdValues::DOUBLETAP)
{
DEBUGLOG("Lead state updated. newState: %d", stateChange.newState);
DoubleTAPEnabled = !DoubleTAPEnabled;
}
break;
}
}
}
this is our main fuction in ontimer
void DataLoggerClient::startDataLoggerAcc()
{
DEBUGLOG(" startDataLogger ");
WB_RES::DataEntry entry;
entry.path = "/Meas/Acc/13";
WB_RES::DataLoggerConfig dataLoggerConfig;
WB_RES::DataEntry entries[] = {entry};
dataLoggerConfig.dataEntries.dataEntry = wb::MakeArray<WB_RES::DataEntry>(entries, 1);
wb::Result configureResult = asyncPut(WB_RES::LOCAL::MEM_DATALOGGER_CONFIG(), AsyncRequestOptions::Empty, dataLoggerConfig);
if (!wb::RETURN_OK(configureResult))
{
DEBUGLOG("Datalogger configuring failed: %u", configureResult);
// return false;
}
wb::Result stateResult = asyncPut(
WB_RES::LOCAL::MEM_DATALOGGER_STATE(), AsyncRequestOptions::Empty,
WB_RES::DataLoggerStateValues::Type::DATALOGGER_LOGGING);
if (wb::RETURN_OK(stateResult))
{
DEBUGLOG("Datalogger enabling success: %u", stateResult);
// return false;
}
if (!wb::RETURN_OK(stateResult))
{
DEBUGLOG("Datalogger enabling failed: %u", stateResult);
// return false;
}
// return true;
}
we are succsefully work dataloger start or stop with doubletap in this path "Meas/HR" but i am unable to stop datalogger in this path "/Meas/Acc/104"
i am try with "/Meas/HR" start or stop using doubletap its work fine but i am only session start in "/Meas/Acc/13" and i am unable to stop session using doubletap.
i am expecting datalogger start or stop using doubletap in this path "/Meas/Acc/13".
