My system is freezing several 15-60 seconds randomly.
The SSD was working fine on my previous computer. And I put it to my new computer. There are many errors in smartctl and journalctl -k. Internet resources say check the SATA cable but I'm not sure if it's really the problem. The most concerning is I think in smartctl
0x0001 4 269 Command failed due to ICRC error
Debian 13 sid. kernel v. 6.12.27-amd64 - motherboard is msi x670e
root@memo:/home/memo# smartctl -ax /dev/sda2
smartctl 7.4 2023-08-01 r5530 [x86_64-linux-6.12.27-amd64] (local build)
Copyright (C) 2002-23, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: Phison Driven SSDs
Device Model: KINGSTON SA400S37960G
Serial Number: 50026B7382E64E6E
LU WWN Device Id: 5 0026b7 382e64e6e
Firmware Version: SAM22101
User Capacity: 960,197,124,096 bytes [960 GB]
Sector Size: 512 bytes logical/physical
Rotation Rate: Solid State Device
TRIM Command: Available
Device is: In smartctl database 7.3/5528
ATA Version is: ACS-3 T13/2161-D revision 4
SATA Version is: SATA 3.2, 6.0 Gb/s (current: 6.0 Gb/s)
Local Time is: Thu May 29 19:16:50 2025 EEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
AAM feature is: Unavailable
APM feature is: Disabled
Rd look-ahead is: Enabled
Write cache is: Enabled
DSN feature is: Unavailable
ATA Security is: Disabled, frozen [SEC2]
Wt Cache Reorder: Unavailable
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 120) seconds.
Offline data collection
capabilities: (0x11) SMART execute Offline immediate.
No Auto Offline data collection support.
Suspend Offline collection upon new
command.
No Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
No Selective Self-test supported.
SMART capabilities: (0x0002) Does not save SMART data before
entering power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 10) minutes.
SMART Attributes Data Structure revision number: 1
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE
1 Raw_Read_Error_Rate -O--CK 100 100 000 - 100
9 Power_On_Hours -O--CK 100 100 000 - 1133
12 Power_Cycle_Count -O--CK 100 100 000 - 626
148 Unknown_Attribute ------ 100 100 000 - 0
149 Unknown_Attribute ------ 100 100 000 - 0
167 Write_Protect_Mode ------ 100 100 000 - 0
168 SATA_Phy_Error_Count -O--C- 100 100 000 - 86
169 Bad_Block_Rate ------ 100 100 000 - 0
170 Bad_Blk_Ct_Lat/Erl ------ 100 100 010 - 0/0
172 Erase_Fail_Count -O--CK 100 100 000 - 0
173 MaxAvgErase_Ct ------ 100 100 000 - 0
181 Program_Fail_Count -O--CK 100 100 000 - 0
182 Erase_Fail_Count ------ 100 100 000 - 0
187 Reported_Uncorrect -O--CK 100 100 000 - 0
192 Unsafe_Shutdown_Count -O--C- 100 100 000 - 89
194 Temperature_Celsius -O---K 024 032 000 - 24 (Min/Max 20/32)
196 Reallocated_Event_Count -O--CK 100 100 000 - 0
199 SATA_CRC_Error_Count -O--CK 100 100 000 - 0
218 CRC_Error_Count -O--CK 100 100 000 - 86
231 SSD_Life_Left ------ 100 100 000 - 100
233 Flash_Writes_GiB -O--CK 100 100 000 - 5824
241 Lifetime_Writes_GiB -O--CK 100 100 000 - 4763
242 Lifetime_Reads_GiB -O--CK 100 100 000 - 929
244 Average_Erase_Count ------ 100 100 000 - 7
245 Max_Erase_Count ------ 100 100 000 - 9
246 Total_Erase_Count ------ 100 100 000 - 1689
||||||_ K auto-keep
|||||__ C event count
||||___ R error rate
|||____ S speed/performance
||_____ O updated online
|______ P prefailure warning
General Purpose Log Directory Version 1
SMART Log Directory Version 1 [multi-sector log support]
Address Access R/W Size Description
0x00 GPL,SL R/O 1 Log Directory
0x01 SL R/O 1 Summary SMART error log
0x02 SL R/O 1 Comprehensive SMART error log
0x03 GPL R/O 1 Ext. Comprehensive SMART error log
0x04 GPL,SL R/O 8 Device Statistics log
0x06 SL R/O 1 SMART self-test log
0x07 GPL R/O 1 Extended self-test log
0x10 GPL R/O 1 NCQ Command Error log
0x11 GPL R/O 1 SATA Phy Event Counters log
0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log
0x80-0x9f GPL,SL R/W 16 Host vendor specific log
0xde GPL VS 8 Device vendor specific log
SMART Extended Comprehensive Error Log Version: 1 (1 sectors)
Device Error Count: 86 (device log contains only the most recent 4 errors)
CR = Command Register
FEATR = Features Register
COUNT = Count (was: Sector Count) Register
LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8
LH = LBA High (was: Cylinder High) Register ] LBA
LM = LBA Mid (was: Cylinder Low) Register ] Register
LL = LBA Low (was: Sector Number) Register ]
DV = Device (was: Device/Head) Register
DC = Device Control Register
ER = Error register
ST = Status register
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 86 [1] log entry is empty
Error 85 [0] log entry is empty
Error 84 [3] log entry is empty
Error 83 [2] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
00 -- 00 00 00 00 00 00 00 00 00 00 00
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
b0 00 d1 01 01 00 00 4f 00 c2 01 00 08 00:00:00.000 SMART READ ATTRIBUTE THRESHOLDS [OBS-4]
2f 00 00 01 01 00 00 00 00 00 03 00 08 00:00:00.000 READ LOG EXT
2f 00 00 01 01 00 00 00 00 00 00 00 08 00:00:00.000 READ LOG EXT
b0 00 d5 01 01 00 00 4f 00 c2 00 00 08 00:00:00.000 SMART READ LOG
b0 00 da 00 00 00 00 4f 00 c2 00 00 08 00:00:00.000 SMART RETURN STATUS
SMART Error Log Version: 1
Warning: ATA error count 0 inconsistent with error log pointer 1
ATA Error Count: 0
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 0 occurred at disk power-on lifetime: 0 hours (0 days + 0 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
00 00 00 00 00 00 00 at LBA = 0x00000000 = 0
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
60 00 28 70 b6 60 00 00 00:00:00.000 READ FPDMA QUEUED
60 50 70 f8 b8 40 00 00 00:00:00.000 READ FPDMA QUEUED
60 08 98 80 1c e4 00 00 00:00:00.000 READ FPDMA QUEUED
60 88 a0 e0 01 51 00 00 00:00:00.000 READ FPDMA QUEUED
60 00 80 70 ba 60 00 00 00:00:00.000 READ FPDMA QUEUED
Error -1 occurred at disk power-on lifetime: 0 hours (0 days + 0 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
00 00 00 00 00 00 00
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
e5 00 00 00 00 00 00 08 00:00:00.000 CHECK POWER MODE
b0 da 00 00 4f c2 00 08 00:00:00.000 SMART RETURN STATUS
b0 d0 01 00 4f c2 00 08 00:00:00.000 SMART READ DATA
b0 d5 01 06 4f c2 00 08 00:00:00.000 SMART READ LOG
b0 d5 01 01 4f c2 00 08 00:00:00.000 SMART READ LOG
Error -2 occurred at disk power-on lifetime: 0 hours (0 days + 0 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
00 00 00 00 00 00 00
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
b0 d5 01 06 4f c2 00 08 00:00:00.000 SMART READ LOG
b0 d0 01 00 4f c2 00 08 00:00:00.000 SMART READ DATA
b0 da 00 00 4f c2 00 08 00:00:00.000 SMART RETURN STATUS
b0 d8 00 01 4f c2 00 08 00:00:00.000 SMART ENABLE OPERATIONS
b0 d5 01 01 4f c2 00 08 00:00:00.000 SMART READ LOG
Error -3 occurred at disk power-on lifetime: 0 hours (0 days + 0 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
00 00 00 00 00 00 00
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
e5 00 00 00 00 00 00 08 00:00:00.000 CHECK POWER MODE
b0 da 00 00 4f c2 00 08 00:00:00.000 SMART RETURN STATUS
b0 d0 01 00 4f c2 00 08 00:00:00.000 SMART READ DATA
b0 d5 01 06 4f c2 00 08 00:00:00.000 SMART READ LOG
b0 d5 01 01 4f c2 00 08 00:00:00.000 SMART READ LOG
Error -4 occurred at disk power-on lifetime: 0 hours (0 days + 0 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
00 00 00 00 00 00 00
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
b0 da 00 00 4f c2 00 08 00:00:00.000 SMART RETURN STATUS
b0 d5 01 00 4f c2 00 08 00:00:00.000 SMART READ LOG
2f 00 01 00 00 00 00 08 00:00:00.000 READ LOG EXT
2f 00 01 03 00 00 00 08 00:00:00.000 READ LOG EXT
b0 d5 01 01 4f c2 00 08 00:00:00.000 SMART READ LOG
SMART Extended Self-test Log Version: 1 (1 sectors)
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
1 Short offline Aborted by host 90% 1 -
2 Short offline Aborted by host 90% 1 -
3 Short offline Aborted by host 90% 1 -
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
1 Short offline Aborted by host 90% 1 -
2 Short offline Aborted by host 90% 1 -
3 Short offline Aborted by host 90% 1 -
Selective Self-tests/Logging not supported
SCT Commands not supported
Device Statistics (GP Log 0x04)
Page Offset Size Value Flags Description
0x01 ===== = = === == General Statistics (rev 1) ==
0x01 0x008 4 626 --- Lifetime Power-On Resets
0x01 0x010 4 1133 --- Power-on Hours
0x01 0x018 6 1399104845 --- Logical Sectors Written
0x01 0x020 6 48026 --- Number of Write Commands
0x01 0x028 6 1950235430 --- Logical Sectors Read
0x01 0x030 6 95596 --- Number of Read Commands
0x07 ===== = = === == Solid State Device Statistics (rev 1) ==
0x07 0x008 1 9 --- Percentage Used Endurance Indicator
|||_ C monitored condition met
||__ D supports DSN
|___ N normalized value
Pending Defects log (GP Log 0x0c) not supported
SATA Phy Event Counters (GP Log 0x11)
ID Size Value Description
0x0001 4 269 Command failed due to ICRC error
0x0002 4 1 R_ERR response for data FIS
0x0005 4 0 R_ERR response for non-data FIS
0x000a 4 3 Device-to-host register FISes sent due to a COMRESET
-- Not only READ WRITE PDFMA but I saw also EXT FS CHECK errors etc
ata10.00: exception Emask 0x2 SAct 0x7effffff SErr 0xed0400 action 0x6 frozen
May 29 19:10:14 memo kernel: ata10: SError: { Proto PHYRdyChg CommWake 10B8B BadCRC Handshk LinkSeq }
May 29 19:10:14 memo kernel: ata10.00: failed command: WRITE FPDMA QUEUED
May 29 19:10:14 memo kernel: ata10.00: cmd 61/08:00:10:54:29/00:00:60:00:00/40 tag 0 ncq dma 4096 out
May 29 19:10:14 memo kernel: ata10.00: status: { DRDY }
May 29 19:10:14 memo kernel: ata10.00: failed command: WRITE FPDMA QUEUED
May 29 19:10:14 memo kernel: ata10.00: cmd 61/08:08:78:56:29/00:00:60:00:00/40 tag 1 ncq dma 4096 out
May 29 19:10:14 memo kernel: ata10.00: status: { DRDY }
May 29 19:10:14 memo kernel: ata10.00: failed command: WRITE FPDMA QUEUED
May 29 19:10:14 memo kernel: ata10.00: cmd 61/08:10:50:59:29/00:00:60:00:00/40 tag 2 ncq dma 4096 out
May 29 19:10:14 memo kernel: ata10.00: status: { DRDY }
May 29 19:10:14 memo kernel: ata10.00: failed command: READ FPDMA QUEUED
May 29 19:10:14 memo kernel: ata10.00: cmd 60/18:18:00:db:5e/00:00:62:00:00/40 tag 3 ncq dma 12288 in
May 29 19:10:14 memo kernel: ata10.00: status: { DRDY }
May 29 19:10:14 memo kernel: ata10.00: failed command: READ FPDMA QUEUED
May 29 19:10:14 memo kernel: ata10.00: cmd 60/08:20:18:db:5e/00:00:62:00:00/40 tag 4 ncq dma 4096 in
May 29 19:10:14 memo kernel: ata10.00: status: { DRDY }
May 29 19:10:14 memo kernel: ata10.00: failed command: READ FPDMA QUEUED
May 29 19:10:14 memo kernel: ata10.00: cmd 60/e8:28:20:db:5e/00:00:62:00:00/40 tag 5 ncq dma 118784 in
May 29 19:10:14 memo kernel: ata10.00: status: { DRDY }
May 29 19:10:14 memo kernel: ata10.00: failed command: READ FPDMA QUEUED
May 29 19:10:14 memo kernel: ata10.00: cmd 60/c8:30:00:da:5e/00:00:62:00:00/40 tag 6 ncq dma 102400 in
May 29 19:10:14 memo kernel: ata10.00: status: { DRDY }
May 29 19:10:14 memo kernel: ata10.00: failed command: READ FPDMA QUEUED
May 29 19:10:14 memo kernel: ata10.00: cmd 60/08:38:c8:da:5e/00:00:62:00:00/40 tag 7 ncq dma 4096 in
May 29 19:10:14 memo kernel: ata10.00: status: { DRDY }
May 29 19:10:14 memo kernel: ata10.00: failed command: READ FPDMA QUEUED
May 29 19:10:14 memo kernel: ata10.00: cmd 60/30:40:d0:da:5e/00:00:62:00:00/40 tag 8 ncq dma 24576 in
May 29 19:10:14 memo kernel: ata10.00: status: { DRDY }
May 29 19:10:14 memo kernel: ata10.00: failed command: WRITE FPDMA QUEUED
May 29 19:10:14 memo kernel: ata10.00: cmd 61/40:48:a8:ca:f9/05:00:35:00:00/40 tag 9 ncq dma 688128 out
May 29 19:10:14 memo kernel: ata10.00: status: { DRDY }
May 29 19:10:14 memo kernel: ata10.00: failed command: WRITE FPDMA QUEUED
May 29 19:10:14 memo kernel: ata10.00: cmd 61/40:50:e8:cf:f9/05:00:35:00:00/40 tag 10 ncq dma 688128 out
May 29 19:10:14 memo kernel: ata10.00: status: { DRDY }
May 29 19:10:14 memo kernel: ata10.00: failed command: READ FPDMA QUEUED
May 29 19:10:14 memo kernel: ata10.00: cmd 60/08:58:20:dd:5e/00:00:62:00:00/40 tag 11 ncq dma 4096 in
May 29 19:10:14 memo kernel: ata10.00: status: { DRDY }
May 29 19:10:14 memo kernel: ata10.00: failed command: WRITE FPDMA QUEUED
May 29 19:10:14 memo kernel: ata10.00: cmd 61/40:60:28:d5:f9/05:00:35:00:00/40 tag 12 ncq dma 688128 out
May 29 19:10:14 memo kernel: ata10.00: status: { DRDY }
May 29 19:10:14 memo kernel: ata10.00: failed command: WRITE FPDMA QUEUED
May 29 19:10:14 memo kernel: ata10.00: cmd 61/40:68:68:da:f9/05:00:35:00:00/40 tag 13 ncq dma 688128 out
May 29 19:10:14 memo kernel: ata10.00: status: { DRDY }
May 29 19:10:14 memo kernel: ata10.00: failed command: WRITE FPDMA QUEUED
May 29 19:10:14 memo kernel: ata10.00: cmd 61/40:70:a8:df:f9/05:00:35:00:00/40 tag 14 ncq dma 688128 out
May 29 19:10:14 memo kernel: ata10.00: status: { DRDY }
May 29 19:10:14 memo kernel: ata10.00: failed command: READ FPDMA QUEUED
May 29 19:10:14 memo kernel: ata10.00: cmd 60/08:78:48:96:a0/00:00:62:00:00/40 tag 15 ncq dma 4096 in
May 29 19:10:14 memo kernel: ata10.00: status: { DRDY }
May 29 19:10:14 memo kernel: ata10.00: failed command: READ FPDMA QUEUED
May 29 19:10:14 memo kernel: ata10.00: cmd 60/00:80:50:9a:11/01:00:31:00:00/40 tag 16 ncq dma 131072 in
May 29 19:10:14 memo kernel: ata10.00: status: { DRDY }
May 29 19:10:14 memo kernel: ata10.00: failed command: WRITE FPDMA QUEUED
May 29 19:10:14 memo kernel: ata10.00: cmd 61/40:88:e8:e4:f9/05:00:35:00:00/40 tag 17 ncq dma 688128 out
May 29 19:10:14 memo kernel: ata10.00: status: { DRDY }
May 29 19:10:14 memo kernel: ata10.00: failed command: WRITE FPDMA QUEUED
May 29 19:10:14 memo kernel: ata10.00: cmd 61/98:90:28:ea:f9/03:00:35:00:00/40 tag 18 ncq dma 471040 out
May 29 19:10:14 memo kernel: ata10.00: status: { DRDY }
May 29 19:10:14 memo kernel: ata10.00: failed command: WRITE FPDMA QUEUED
May 29 19:10:14 memo kernel: ata10.00: cmd 61/08:98:18:4d:29/00:00:60:00:00/40 tag 19 ncq dma 4096 out
May 29 19:10:14 memo kernel: ata10.00: status: { DRDY }
May 29 19:10:14 memo kernel: ata10.00: failed command: READ FPDMA QUEUED
May 29 19:10:14 memo kernel: ata10.00: cmd 60/20:a0:00:dd:5e/00:00:62:00:00/40 tag 20 ncq dma 16384 in
May 29 19:10:14 memo kernel: ata10.00: status: { DRDY }
May 29 19:10:14 memo kernel: ata10.00: failed command: READ FPDMA QUEUED
May 29 19:10:14 memo kernel: ata10.00: cmd 60/40:a8:38:dd:5e/00:00:62:00:00/40 tag 21 ncq dma 32768 in
May 29 19:10:14 memo kernel: ata10.00: status: { DRDY }
May 29 19:10:14 memo kernel: ata10.00: failed command: READ FPDMA QUEUED
May 29 19:10:14 memo kernel: ata10.00: cmd 60/88:b0:78:dd:5e/00:00:62:00:00/40 tag 22 ncq dma 69632 in
May 29 19:10:14 memo kernel: ata10.00: status: { DRDY }
May 29 19:10:14 memo kernel: ata10.00: failed command: READ FPDMA QUEUED
May 29 19:10:14 memo kernel: ata10.00: cmd 60/08:b8:30:dd:5e/00:00:62:00:00/40 tag 23 ncq dma 4096 in
May 29 19:10:14 memo kernel: ata10.00: status: { DRDY }
May 29 19:10:14 memo kernel: ata10.00: failed command: READ FPDMA QUEUED
May 29 19:10:14 memo kernel: ata10.00: cmd 60/08:c8:00:b1:10/00:00:02:00:00/40 tag 25 ncq dma 4096 in
May 29 19:10:14 memo kernel: ata10.00: status: { DRDY }
May 29 19:10:14 memo kernel: ata10.00: failed command: READ FPDMA QUEUED
May 29 19:10:14 memo kernel: ata10.00: cmd 60/08:d0:28:dd:5e/00:00:62:00:00/40 tag 26 ncq dma 4096 in
May 29 19:10:14 memo kernel: ata10.00: status: { DRDY }
May 29 19:10:14 memo kernel: ata10.00: failed command: WRITE FPDMA QUEUED
May 29 19:10:14 memo kernel: ata10.00: cmd 61/08:d8:68:50:29/00:00:60:00:00/40 tag 27 ncq dma 4096 out
May 29 19:10:14 memo kernel: ata10.00: status: { DRDY }
May 29 19:10:14 memo kernel: ata10.00: failed command: WRITE FPDMA QUEUED
May 29 19:10:14 memo kernel: ata10.00: cmd 61/08:e0:00:52:29/00:00:60:00:00/40 tag 28 ncq dma 4096 out
May 29 19:10:14 memo kernel: ata10.00: status: { DRDY }
May 29 19:10:14 memo kernel: ata10.00: failed command: WRITE FPDMA QUEUED
May 29 19:10:14 memo kernel: ata10.00: cmd 61/08:e8:e8:52:29/00:00:60:00:00/40 tag 29 ncq dma 4096 out
May 29 19:10:14 memo kernel: ata10.00: status: { DRDY }
May 29 19:10:14 memo kernel: ata10.00: failed command: WRITE FPDMA QUEUED
May 29 19:10:14 memo kernel: ata10.00: cmd 61/08:f0:98:53:29/00:00:60:00:00/40 tag 30 ncq dma 4096 out
May 29 19:10:14 memo kernel: ata10.00: status: { DRDY }
May 29 19:10:14 memo kernel: ata10: hard resetting link
May 29 19:10:14 memo kernel: ata10: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
May 29 19:10:14 memo kernel: ata10.00: configured for UDMA/133
May 29 19:10:14 memo kernel: ata10: EH complete
